fast cooling

美 [fæst ˈkuːlɪŋ]英 [fɑːst ˈkuːlɪŋ]
  • 快速冷却;快速降温
fast coolingfast cooling
  1. The utility model relates to a multifunctional cup which is capable of heat preservation , fast cooling and heating up and clearly displaying temperature and volume .

    一种能保温、快速降温和升温、清楚显示温度和容量的多功能杯子。

  2. Design on the Fast Cooling System of Furnace

    加热炉速冷系统的设计

  3. Fast cooling in heat treatment can decrease magnetic flux density .

    快速冷却可降低钢的磁通密度。

  4. So it is an important value to investigate the fast cooling technology of turbine .

    目前,虽然关于汽轮机快速冷却技术研究较多,且许多电厂采用了快速冷却技术,但其应用效果较差,因而进行汽轮机优化冷却技术的研究具有重要的工程实用价值。

  5. Simulation on Temperature Field Under Ultra Fast Cooling

    超快冷却条件下温度场数值模拟

  6. Necessity , Feasibility and Method of Fast Cooling for HP Heaters

    高压加热器快冷的必要性、可行性和快冷方法

  7. Fast cooling speed was the main reason of generating cold crackle .

    认为冷却速度过快是产生冷裂纹的主要原因。

  8. Study on Application of Ultra Fast Cooling to Thin Slab Casting and Rolling Production Line

    超快速冷却技术在短流程热带钢生产线上的应用分析

  9. Heat Transfer of Hot Strip During Ultra Fast Cooling

    热轧带钢超快速冷却过程的换热分析

  10. Two roads slow heating , fast cooling .

    路面加热升温慢,降温快。

  11. Development of ultra fast cooling technology Ultra-micro Carrier Super Acids

    超快冷却技术的发展

  12. Analysis of the Necessity of Installing A Fast Cooling Device for a Steam Turbine

    设置汽轮机快速冷却装置的必要性分析

  13. Study on the Thermo-flux Theory of Al-Li Alloys Fast Cooling Powder Process

    Al-Li合金快冷制粉过程的热流理论分析

  14. Effect of fast cooling on mechanical properties of continuous annealed cold rolled ultra high strength steel

    连续退火快冷工艺对冷轧超高强钢力学性能的影响

  15. In this paper , melting and fast cooling method is used to produce Fe-C compounds .

    本文采用熔铸速冷法制备Fe-C化合物,合成了含碳量为共晶成分的Fe-C化合物。

  16. The production line is provided with the function of continuous reverting for rod surface and fast cooling .

    生产线具有铜杆表面连续还原、速冷却功能。

  17. Cold Mountain So it is completely feasible in theory for fast cooling of HP heaters .

    因此,高压加热器的快冷在理论上是完全可行的。

  18. Research on a fast cooling process of the spacer grids for nuclear fuel assembly after soldering-aging

    核元件定位格架钎焊的快速冷却工艺研究

  19. Because of the fast cooling of flowing medium , the hydrogen cracking occurs easily under in-service welding .

    在役焊接过程中,管内流动介质的快速冷却,易使接头出现氢致裂纹。

  20. The Influence of Micro Alloying and Fast Cooling after Rolling on Microstructures and Mechanical Properties of Hot Ribbed Bars

    微合金化配合轧后快速冷却对热轧带肋钢筋组织和性能的影响

  21. The author investigates nucleation mechanism of alumina dendrites in Al deoxidized steel by fast cooling samples .

    本文利用快速冷却试样研究了铝脱氧钢液中氧化铝树枝晶的形核机理。

  22. During the fast cooling process of solution treatment , nonequilibrium segregation of manganese was produced at austenite grain boundaries .

    在固溶处理时快速冷却过程中锰在奥氏体晶界产生不平衡偏聚。

  23. However , welding on pipelines with flowing oil and gas may cause hydrogen cracking in HAZ located at the fast cooling .

    但是在不停输情况下焊接,由于管内介质的流动而产生的快冷效果可能会形成热影响区(HAZ)的氢致开裂。

  24. It is common sense in practice that rapid burning in high temperature with fast cooling can rise the quality of Portland cement clinker .

    高温快速煅烧和急速冷却可提高硅酸盐水泥熟料质量是生产实践中得出的共识。

  25. The insufficient stream inoculation and too fast cooling of local area of the casting is the main reason causing the chill defect .

    引起白口的主要原因是随流孕育量不足以及铸件局部冷却速度过快;

  26. Because of fast cooling rate of the surface , the quenching temperature has little effect on the microstructure of the external part , basically for the martensite .

    在淬火时的快速冷却下,由于表面冷却速度极快,淬火温度对试样边缘组织影响不大,基本都为马氏体组织。

  27. Needle shape of the apatites and amphiboles in MMEs implying the process of fast cooling .

    包体中发育针状磷灰石和角闪石,显示为岩浆淬冷的结果。

  28. It should be payed much attention to fast cooling because it can decrease the defects of PCB assemblies and promote the reliability of solder joint .

    研究现状表明快速冷却有助于减少焊接缺陷,提高焊点可靠性。

  29. It showed that a fast cooling after drawing was of benefit to dimensional stability , straightness , environmental stress cracking resistance , and strength of the drawn tubes .

    拉伸时的自然冷却会产生不均匀的产品,快速水冷却拉伸工艺能显著改善管的耐环境应力开裂性,成倍提高其强度。

  30. Reverse modeling of fission track data with correlative software show that all samples had experienced fast cooling episodes before 70 ~ 60 Ma and since about 10 Ma .

    通过相关软件对不同磷灰石裂变径迹数据模拟,显示在70~60Ma前及约10Ma开始出现快速抬升(冷却)。